Recent content by ccreddell

  1. ccreddell

    Tbi no injector pulse and or tbi removal

    Ran into the same problem with a truck I picked up at a county auction. It was the injector driver in the ECM. I happened to have a spare ECM with the same part number on it, so I just swapped the prom and it has run like a jewel ever since. Oh, it was a 94 3/4T with a 350. Got it for $200.
  2. ccreddell

    5.7L Cold Air Intakes?

    The thing about most cowl hoods is that they are open underneath. You would need to sheet the underside of the hood with aluminum or something thin and light and then cut out an opening above the throttle body. Then it would be fairly easy to bend up a box with a open top (probably with a...
  3. ccreddell

    C4 corvette irs installation.

    Something else I just found-and now my wheels are turning! Kept me up late a couple nights now... https://rick486.wixsite.com/dobbertinperformance
  4. ccreddell

    The Center Console Thread

    I gutted mine and ran a regular old amp I had sitting around. Sounds excellent and way bigger than it should.
  5. ccreddell

    Core shifters back in stock

    Check out the drill mod the F-body crowd used to do. Theres a restriction built into the hose down to the slave cylinder that restricts the flow just so we cant shift without lifting. Open that up and it reacts just as fast as mechanical linkage.
  6. ccreddell

    Good ready to install vortec heads?+cam recommendation

    For a (relatively) cheap set up, I ran an LT1 cam when I changed over to Vortec heads. Ran an adapter and the stock TBI. Had to change over to roller lifter, and I ran 1.6 roller rockers and that truck ran very well and with a bit of tuning I got better than 20mpg on the highway.
  7. ccreddell

    Tire width on your low OBS

    Picture down below-255/40/20, 285/40/20
  8. ccreddell

    '89 Stepside "Way Cool Jr."

    8-Lug. Not a 1500...
  9. ccreddell

    '89 Stepside "Way Cool Jr."

    Im running timing with a Small Cap HEI and a TBI coil.....
  10. ccreddell

    GMT 800 front brake upgrade to GMT400 8 lug

    In one of his other videos, he did the rear end swap.
  11. ccreddell

    Vortec headed tbi to carb swap - wiring and 700r4 lockup

    On my 90, I built a 383, did the vrfpr, ran a 7.4L TBI with the 2" factory spacer that mounts to Edelbrock spreadbore mani. I think the cam is a comp 268 roller. Oh, and I run the FLASH ECM. I finally got it to run, but really badly. Could seem to get it tuned. So, I'm in the process of slapping...
  12. ccreddell

    Sniper EFI conversion

    Im still putting it together. I have to replace my whole fuel system (because I wanted to), and Im doing it in the driveway. Heat in the PNW has been 102-105 for a couple weeks now, so that has slowed me down. But hopefully soon....
  13. ccreddell

    NBS/Astro knuckle brake upgrade.

    https://www.shopchevyparts.com/performance/2021-tahoe-performance-front-brake-upgrade-system-brembo-piston-red-chevrolet-performance-logo/84766666-p-92309631.html At $2000+ Im thinking the 13" rotor and 4-piston caliper would be enough for me....
  14. ccreddell

    Original Owner 94 K1500 Stepside Extended Cab

    Im curious about the controller mounting. That is clean. Any idea how they did that?
  15. ccreddell

    NBS/Astro knuckle brake upgrade.

    Yeah, I was already there on the 4 piston caliper thing....
Top