Recent content by 96redchev

  1. 96redchev

    No oil pressure at idle

    No it was just shavings on the drain plug one of the bearings are beginning to make noise on the front of the block
  2. 96redchev

    No oil pressure at idle

    Yes it’s the oil pressure sensor unfortunately yes the timing was severely out of wack
  3. 96redchev

    No oil pressure at idle

    Yes that’s what I meant unfortunately I threw it away the metal was extremely fine. I figured out it jumped timing when I went to replace the sensor and the entire distributor assembly came strait up part of the plastic ring was snapped off in return it was refusing to turn over I have two...
  4. 96redchev

    No oil pressure at idle

    Yes once I come to a stop of let it idle in park the light comes on but so when it jumped timing( was not aware it was out of timing when this occurred ) I lost all pressure and parked it immediately. I assumed the sensor was bad since it is the original. no bad noises. But the bearing on the...
  5. 96redchev

    No oil pressure at idle

    Yes once I come to a stop of let it idle in park the light comes on
  6. 96redchev

    No oil pressure at idle

    So I have a 96 5.0 with 226k I just replaced the oil pressure sensor when idling at operating temp it says check gurgles shows no pressure I idle at about 650 700 if I bump the throttle to take it to 1000 I have about 15 to 20 psi running down the road at 70 it’s steady at 40 I don’t know if the...
  7. 96redchev

    I have flashers when ether blinker is turned on

    so when I turn ether blinker on I get hazards but I also get them on the dash when the lights are turned on. The dome light comes on but dim when the truck is turned on also the 3rd break light stays on after truck is turned on. I have all led front and back I have the resister on one blinker on...
  8. 96redchev

    The Stupid Electronics Questions Thread

    so when I turn ether blinker on I get hazards but I also get them on the dash when the lights are turned on. The dome light comes on but dim when the truck is turned on also the 3rd break light stays on after truck is turned on. I have all led front and back I have the resister on one blinker on...
  9. 96redchev

    I have flashers when ether blinker is turned on

    And now my dome light stays. Faint with the pickup off as well as the 3rd brake light
  10. 96redchev

    I have flashers when ether blinker is turned on

    only the same color to same color I spliced the resistors in
  11. 96redchev

    I have flashers when ether blinker is turned on

    So this is a mess right now it will be cleaned up once everything is figure out but I have one on each side and it’s still giving me the issue of not blinking on the passenger side when the lights are turned on driver side still works fine also the light for the gear selector dims when the...
  12. 96redchev

    I have flashers when ether blinker is turned on

    Okay thanks again I have two on each side so that must be the issue
  13. 96redchev

    I have flashers when ether blinker is turned on

    Also yes I have leds front and back except for headlights
  14. 96redchev

    I have flashers when ether blinker is turned on

    Thank you I’ll get that put together. So I only need the resistor on one blinker ? Or do I need them on each separate wire?
  15. 96redchev

    I have flashers when ether blinker is turned on

    I did check that I cleaned it but maybe not well enough. would running a ground from the battery to the frame change anything? or be pointless I also have the aftermarket flasher that makes it ignore the leds
See more

Latest posts

Staff online

Members online

Total: 1,182 (members: 31, guests: 1,151)

Forum statistics

Threads
64,582
Messages
1,396,975
Members
52,052
Latest member
DColeman

Share this page

Top