-
-
11989GMCSIERRA replied to the thread Changing tires fast ‘ Going opposite ways ..Need opinions on what will ride smoother and be good for a 5k suv ”.best tires i ever tan and still do on the street are Michelins
-
11989GMCSIERRA replied to the thread Am I underpowered?.3/4 tons don't come with V6s. he's either got a 350 or a 454 maybe a diesel? i'm leaning to 350. i'm not sure what you mean by "built...
-
11989GMCSIERRA replied to the thread Cab Mount Replacement Procedure.the cab mounts get replaced the exact same way as if you were installing a body lift. loosen bolts on all mounts. remove mount bolts...
-
11989GMCSIERRA replied to the thread Can a Th700r4 be used for towing?.At the weight you’re planning on hauling that whole truck isn’t gonna do the job. 11,500 pounds is a lot to ask out of a 90s Chevy. And...
-
11989GMCSIERRA replied to the thread Smoke coming from exhaust.If your car ran fine after you replaced the plugs and it’s not overheating you could be throwing away a perfectly good engine for a worn...
-
11989GMCSIERRA replied to the thread What aftermarket air cleaners will fit on a gen 5 tbi 454.The big plastic oval silencer should have a reducing cone inside. Just remove that. That’s what I did. Personally I wouldn’t run a open...
-
11989GMCSIERRA replied to the thread 305 TBI Header (?)s.The few times I used headers either for my vehicles or friends I went with Gibson.
-
11989GMCSIERRA replied to the thread 305 TBI Header (?)s.It’s all good man. I actually like stock looking trucks. I don’t have a issue buying thjgs I need. For example my camping hunting truck...
-
11989GMCSIERRA replied to the thread 305 TBI Header (?)s.I wouldn’t spend the money. Seriously just get the truck running right, put stock cast iron manifolds and of the sun cabs it is rotted...
-
11989GMCSIERRA replied to the thread Crank, no start..where was the 55psi reading taken from in the fuel system? What is your fuel pressure at the rail? If it’s lower check then fuel...
-
11989GMCSIERRA replied to the thread Bad wheel bearing What to buy.If I replace any hubs I try to see if Timken makes a replacement. If they don’t I get a factory one. Too many fake crappy parts out...
-
11989GMCSIERRA replied to the thread Quad Beam Headlight Refresh.Yeah i have. I’m a electrician by trade. I work with lighting and relays every day. I was doing High Beam on with low beam relays when...
-
11989GMCSIERRA replied to the thread Quad Beam Headlight Refresh.Actually it won’t. It will act as a sealant for a while and “encapsulate the rust” but the rust will eat through eventually. The way...
-
11989GMCSIERRA replied to the thread UCA hitting frame at full travel.You need aftermarket long travel UCAs. You’re gonna break a ball joint jumping that truck or eventually break something . A vehicle...
-
11989GMCSIERRA replied to the thread 1988/89 glass quad headlights: need adjustment procedure + stuck screws.The trim rings won’t line up cause they’ll be upside down if swapped. I don’t think the buckets will bolt in the radiator support cause...
-
-
Loading…
-
Loading…
Members online
- Hipster
- 89RCLB
- smithag18
- Jksconny
- yrusohi
- rosert
- Remodelmaster
- Ozarkburb
- 99xcss4
- Thenamesducky
- GrimsterGMC
- Scooterwrench
- bhack3311014
- Orpedcrow
- kylenautique
- Jay Watson
- 93z71lq9
- Brody
- Supercharged111
- Claymore877
- Rock Hard Concrete
- rdobirdman
- Vladi295
- sicumminsde
- bogthebuilder
- Komet
- PlayingWithTBI
- 0xDEADBEEF
- jwc55
- 96blackswb
- jinks67
- SheMoansObs
- caw_86
- Mattcourt21
- heskahoka
- johnckhall
- Anchor
- Dravec
- Salty K1500
- HotWheelsBurban
- mxmxmc3000
- 6shoot
- Silver 7T8
- Drunkcanuk
- Georgiabigfoot
- Olds455
- Caman96
- Tholoth
- G1kon1wheel
- Cr916