Recent content by 1500z71

  1. 1500z71

    The Stupid Axle Questions Thread

    Who are y'all using for wheel hub assemblies? I am hearing Timken, AC Delco, Moog, and TRQ. Two surprising things I'm seeing though is that Delco and Moog source these parts and they can be crap sometimes. Is Timken from Rock Auto good to go? NOS right? How about TRQ? Rock Auto actually has...
  2. 1500z71

    The Stupid Interior Questions Thread

    https://leonardaccessories.com/product/interior-consoles-texas-saddlebags-pickup-suburban-console I didn’t even know they still made these but my dad has this one in red matching the interior. Still looks brand new, and they got it shortly after they got the truck in like 94 or 95. I very...
  3. 1500z71

    The Stupid Interior Questions Thread

    Where have folks been getting blower motor covers? I have tried junkyard ones before, but they always seem to get destroyed either taking them off or putting them on. At least the ancient ones I've found. My factory one is finally trying to finish itself off this week. This is for a '93. Isn't...
  4. 1500z71

    The Stupid Electronics Questions Thread

    @dougdeep @ralmo94 Well I replaced the switch and nothing changed. Nice to actually have paint on them again though, looks mint. After a while I started noticing I was having to punch my lock/unlock button like 4 or 5 times to shimmy the doors to lock or unlock. Well after that I got the...
  5. 1500z71

    The Stupid Electronics Questions Thread

    Any takers on this one? I’m hoping it may just be a bad light switch but I’m not sure how that would be related. The switch also just in the last few days will not turn the cluster lights on unless I press on it a little bit harder.
  6. 1500z71

    The Stupid Electronics Questions Thread

    Actually just got finished up, it ended up being a pinched wire in the column. Electrical taped and good to go. Do you know if the aftermarket pulse boards are for the intermittent wipers? It has an intermittent switch but a junkyard non-intermittent in there at the moment.
  7. 1500z71

    The Stupid Electronics Questions Thread

    You think it would be the switch itself? Blinkers and everything else work fine
  8. 1500z71

    The Stupid Electronics Questions Thread

    In our '92 the wiper switch has stopped working. The fuse was blown, replaced it, wipers still didn't work. Pressed "wash" and it popped the fuse again. This is all after I broke down the steering column to tighten those famous E8 bolts. I have seen a few posts on this: is it typically an...
  9. 1500z71

    Camaro Door Chime Swap

    Internal fault in the box. Ironically, before I did mine, I never knew there was a seatbelt light in the 88-94 trucks. It never worked and I just assumed that wasn't a thing until they added airbags, but lo and behind the new chime box fixed this and I saw it for the first time ever. Same...
  10. 1500z71

    Stumbling when put in gear?

    Well I haven't forgotten about any of that, what I've replaced so far has been relatively cheap and easy to replace, and I've done it all before over the years. But now it looks like it's time to get into the weeds with and start testing everything like you've suggested. Thank you for your help...
  11. 1500z71

    Stumbling when put in gear?

    Replaced the PCV valve and line, grommet seemed to check out. No dice. It has started to slip back into how it was acting before I did all the EGR valve and lines, just stumbling more often and not immediately catching itself. I unplugged the EGR solenoid and thought it corrected the idle, but...
  12. 1500z71

    Stumbling when put in gear?

    Good idea, that’s something I’ve started to read more into. I will try that tomorrow. No, the brake doesn’t seem to have any effect. It’s only sometimes in park but always in gear. Neutral acts the same as park in that it doesn’t tend to stumble near as often as idle, if ever.
  13. 1500z71

    Stumbling when put in gear?

    I will look into this next, thank you for the idea. Seems like the blades looked fine but I will double check them again.
  14. 1500z71

    Stumbling when put in gear?

    Man fellas I am chasing this thing down and I am so close. Alright, so here’s what I did tonight and how it went: Replaced EGR valve, replaced the line from valve to solenoid and kept the factory boots. Replace the line from the throttle to the MAP and added a new elbow. Started it up and it...
  15. 1500z71

    Stumbling when put in gear?

    Only one bad 90 degree boot. The rest are in good shape. The boot for the MAP line that is on the back of the throttle seems like it has welded itself on there over the years so it gets to stay there...
Top