Recent content by Awest623
-
Hard to find 3D Printed Interior Parts
3d scans have been a pain for me to develop, but it's how I made the vent gauge holder. Only took me about two months- Awest623
- Post #9
- Forum: OEM and Custom Interiors
-
Turn Signal/Parking Light Weird Issue
Interesting. I've never seen ones with the resistors built in- Awest623
- Post #7
- Forum: Feedback, Help and Suggestions
-
Hard to find 3D Printed Interior Parts
I have two printers with a max volume of 256x256x256mm and 306x306x306mm, the smaller one is 2x faster leading to quicker turn-arounds in design iteration. If it can fit in those I can make it- Awest623
- Post #7
- Forum: OEM and Custom Interiors
-
Turn Signal/Parking Light Weird Issue
The "load equalizer" resistors and the LED flasher relay can be found at any auto-parts store.- Awest623
- Post #4
- Forum: Feedback, Help and Suggestions
-
Turn Signal/Parking Light Weird Issue
Hyper-flashing is normal with LEDs. It's a feature in the flasher relay to tell you if a bulb is burnt out. It measures current draw, if the current draw is too low it'll hyper-flash (caused by a burnt out bulb or low current draw LEDs). You have two options: 1, install a set of "load...- Awest623
- Post #3
- Forum: Feedback, Help and Suggestions
-
motor mounts 98 k1500
Off-Road Designs sells some very nice polyurethane mounts. Here they are installed in my truck- Awest623
- Post #11
- Forum: Stock Suspension + Bolt On Kits
-
Hard to find 3D Printed Interior Parts
I'm thinking my next project will be replacement rubber pieces for the 95-98 dash and console cup holders- Awest623
- Post #6
- Forum: OEM and Custom Interiors
-
Hard to find 3D Printed Interior Parts
I don't own one of those trucks but I may be able to do it depending on what you need. What are you looking for?- Awest623
- Post #4
- Forum: OEM and Custom Interiors
-
Hard to find 3D Printed Interior Parts
More pictures- Awest623
- Post #2
- Forum: OEM and Custom Interiors
-
Hard to find 3D Printed Interior Parts
How's everyone doing. Putting this post out to gauge interest in selling some 3d printed parts for our trucks. I have two commercial grade 3d printers capable of doing some very detailed work. I can make parts in a variety of materials, mainly Thermoplastic Polyurethane and Acrylonitrile Styrene...- Awest623
- Thread
- Replies: 8
- Forum: OEM and Custom Interiors
-
12200411 PCM swap for 1996 to 2000 GMT400 trucks
Lextech doesn't visit the forums anymore, hasn't for a long time. As far as I'm aware the wiring "should" be the same.- Awest623
- Post #1,007
- Forum: 96+ Vortec Performance + Computer Swaps
-
411 Swap 383 Vortec Newbie To Tuning. Where To Start?
It can be finicky at times, especially as these trucks get older. Only thing I can say is keep trying, and don't use beta- Awest623
- Post #26
- Forum: Engine Performance + Maintenance
-
1998 push 3 button 1500 stuck in 4low.
Just another note if you haven't tried already, the case will not shift between lo/hi if your regular brake is on. Rolling under 3mph or at a complete stop should not matter, rolling just makes it easier for the case to shift. Trans in neutral or park (try both). And parking brake should not matter.- Awest623
- Post #9
- Forum: Transfer Cases
-
411 Swap 383 Vortec Newbie To Tuning. Where To Start?
Follow this guide for tuning your idle. There's a lot of steps and it'll take a while, but it'll give you a great running engine. Once you finish that, go through and tune your VE table, MAF, and then spark. I recommend you invest in a wideband sensor with a serial output otherwise you won't be...- Awest623
- Post #11
- Forum: Engine Performance + Maintenance
-
NEW DASH!! Paint recommendations?
Get one of these color swatches and match it up- Awest623
- Post #7
- Forum: OEM and Custom Interiors
